User Account

All Pages

A bar of rectangular cross section 20mm times 5mm with a

Assignment Help Mechanical Engineering
Reference no: EM13631695

A bar of rectangular cross section 20mm × 5mm with a central hole of diameter 4mm is subjected to a tensile force F which fluctuates between maximum and minimum values of 10 kN and 8 kN respectively. Determine the safety factor against eventual fatigue failure with a reliability of 50% if the bar is machined from steel with Sut = 324 MPa and sY = 210 MPa.

Reference no: EM13631695

Questions Cloud

A heat pump is absorbing heat from the cold outdoors at : a heat pump is absorbing heat from the cold outdoors at 5oc and supplying heat to a house at 25oc at a rate of 18000
A parallel plate capacitor is immersed in sea water find : a parallel plate capacitor is immersed in sea water. find the ratio of rms conduction current to rms displacement
The heat exchanger is not insulated and is losing heat at a : a heat exchanger is used to heat cold water at 15oc entering at a rate of 2 kgs by hot air at 85oc entering at a rate
What is the phase difference in a youngs double slit : what is the phase difference in a youngs double slit experiment where the intensity is half that of the central
A bar of rectangular cross section 20mm times 5mm with a : a bar of rectangular cross section 20mm times 5mm with a central hole of diameter 4mm is subjected to a tensile force f
The estimate of the population proportion is to be within : the estimate of the population proportion is to be within plus or minus .04 with a 98 percent level of confidence. the
A company studying the productivity of their employees on a : a company studying the productivity of their employees on a new information system was interested in determining if the
After 10 lbhr of the oil is removed from the potato chips : after 10 lbhr of the oil is removed from the potato chips in the separation unit what is the mass fraction of oil on
A biconvex ice lens is made so that the radius of curvature : a biconvex ice lens is made so that the radius of curvature of the front surface is 12.3 cm and that for the back is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Slow expansion is performed while there is heat transfer

a pistoncylinder contains water with quality 75 at 200 kpa. slow expansion is performed while there is heat transfer

  Find the velocity of the satellite relative to that of the

suppose a satellite in geosynchronous orbit has just passed above the international space station with respect to the

  Find the exit velocity of the neon

A turbine takes in 2 kg/s neon at 27C and 200 kPa with negligible velocity. The produced work is 75 kW and 30 kW of heat leaks into the turbine from the surroundings. The neon exits at 100 kPa and 230 K. Find the exit velocity of the neon.

  The thermal conductivity of an insulating material is found

the thermal conductivity of an insulating material is found by casting a 0.1 m thick shell of the insulating material

  Turbomachinery - impulse and reaction turbines

Question about Turbomachinery - Impulse & Reaction Turbines, An impulse air turbine rotor with a blade speed (U) of 300 m/s is measured to have a relative rotor inlet velocity (W_1) of 750 m/s at an angle of 69 degrees and an outlet relative veloc..

  The area at the nozzle inlet is 01m2at the nozzle exit the

air flows steadily at low speed through nozzle distance charging to atmosphere. the area at the nozzle inlet is

  A viscous fluid flows past a flat plate such that the

a viscous fluid flows past a flat plate such that the boundary layer thickness of a distance d from the leading edge is

  Determine the force in each member of the space truss and

determine the force in each member of the space truss and state if the members are in tension or compression. the truss

  Solve for u as a function of y as done in the class for

consider incompressible viscous flow between two very long plates separated by a distance h. the bottom plate is

  The steam exits the turbine at a pressure of 40 kpa and a

a steam turbine has an inlet pressure of 1200 kpa and temperature of 400 degc. the steam exits the turbine at a

  Assuming that the hole introduces a local stress

a ceramic bidet failed catastrophically in normal use causing serious lacerations to the person concerned. the facture

  Calculate the specific heat at constant pressure

Calculate the specific heat at constant pressure, and specific heat at constant volume for propane which is compressed at the following inlet condition;

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd