A 40-mph wind below past your house speeds up as it flows

Assignment Help Mechanical Engineering
Reference no: EM13346284

A 40-mph wind below past your house speeds up as it flows up and over the roof. If the elevation effects are negligible, determine: 6 marks a) The pressure at the point on the roof where the speed is 60 rpm if the pressure in the free stream blowing toward your house is 14.7 psia. Would this effect tend to push the roof down against the house, or would it tend to lift the roof?
3 marks b) The pressure on a window facing the wind if the window is assuming to be a stagnation point. 

Reference no: EM13346284

Questions Cloud

Calculate the force required in direct extrusion of 1100-o : calculate the force required in direct extrusion of 1100-o aluminum from a diameternbspof 6 in. to 2 in. assume that
Consider the following unbalanced reaction what mass of f2 : consider the following unbalanced reaction.p4s f2g pf3gwhat mass of f2 is needed to produce 175 g of pf3 if the
If the vinegar were measured volumetrically eg a pipet what : a. in determining the percent acetic acid in vinegar the mass of each vinegar sample is measured rather than the
A control system is needed to control a small shopping : a control system is needed to control a small shopping center parking lot lighting system and the exterior lighting
A 40-mph wind below past your house speeds up as it flows : a 40-mph wind below past your house speeds up as it flows up and over the roof.nbspif the elevation effects are
Write a mc6812 assembly language program to find the : write a mc6812 assembly language program to find the largest number in an array of ten 8-bit numbers. the array is
If 525ml of 01000 m naoh solution is needed to just : if 5.25ml of 0.1000 m naoh solution is needed to just neutralize excess acid after 20.00 ml of hcl was added to 1.00 g
A reaction of clacium phosphate and sulfuric acid results : a reaction of clacium phosphate and sulfuric acid results in calcium sulfate and phosphoric acid. if 250 grams of
If the 150 lb man fires the o2lb bullet with a horizontal : if the 150 lb man fires the o.2lb bullet with a horizontal muzzle velocity of 3000 fts measured relative to the 600lb

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd