User Account

All Pages

A 200-kg 5-m-wide rectangular gate shown innbspthe figure

Assignment Help Mechanical Engineering
Reference no: EM13344395

A 200-kg, 5-m-wide rectangular gate shown in the figure is hinged at B and leans against the floor at A making an angle of 45 with the horizontal. The gate\ is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate. 

Reference no: EM13344395

Questions Cloud

Give a proposed design and analysisnbspprincipal features : give a proposed design and analysisnbspprincipal features and working principle of any mechanisms using diagrams to
Phosphoric acid can be prepared by reaction of sulfuric : phosphoric acid can be prepared by reaction of sulfuric acid with phosphate rock according to the equation ca3po42
Develop a system to learn morse code the system will : develop a system to learn morse code. the system will have one input and 26 outputs one per letter. the user sends
The density of gold is 1931 gcm3 and the density of : the density of gold is 19.31 gcm3 and the density of platinum is 21.43 gcm3. if equal masses of gold and platinum are
A 200-kg 5-m-wide rectangular gate shown innbspthe figure : a 200-kg 5-m-wide rectangular gate shown innbspthe figure is hinged at b and leans against thenbspfloor at a making an
Use microsoft excel to compare costs from at least three : 1. use microsoft excel to compare costs from at least three different vendors and reasons to accept specific bids.
If 0176 moles of mg have combined with 0220 moles of o what : if 0.176 moles of mg have combined with 0.220 moles of o what is the empirical formula of the
Density measurements can be used to analyze mixtures for : density measurements can be used to analyze mixtures. for example the density of solid sand without air spaces is about
Calculate the temperature of the gas in the tank when the : during an emergency launch operation to fill a missile with rp-4 a kerosene-based fuel the ullage volume of the fuel

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

  Determine the mach number of this plane for the stated limit

Determine the Mach number of this plane for the stated limiting condition.

  Calculate the mass of mixture produced at the mixing stage

calculate the mass of mixture produced at the mixing stage, the mass jam produced from the kettle and the mass od water evaporated from the kettle.

  State what the joints are in the system

State what the joints are in the system and knowledge of computational kinematics explain what you believe is the procedure to calculate each variable.

  Calculate w, q and delta s for the process

Steam at 1000kPa and 300deg C expands to a pressure of 150kPa in a cylinder. If PV = constant during the process, calculate W, Q and delta S for the process.

  What is a 90 percent confidence interval

What is a 90 percent confidence interval for the standard deviation of the thickness of a washer produced by this procedure?

  What is the eccentricity

A satellite is in Earth with an altitude at perigee of 550 km and an altitude at apogee of 5000 km.

  Explain mechnical vibration analysis

Mechnical Vibration Analysis, How do I deduce the value of the viscous damping factor? How do I deduce the value of the viscous damping coefficient c?

  What is the reason for the change in enthalpy

what is the reason for the change in enthalpy between the throttle valve and the evaporator in a practical refrigeration cycle that is using R12 refrigerant.

  Vital information about overall heat transfer coefficient

Important information about Overall Heat Transfer Coefficient A copper sphere of internal diameter 2 m and wall thickness 40 mm is insulated with 75 mm of expanded polystyrene

  Determine the stress in a stay at a given temperature

Determine the stress in a stay at a given temperature. A steel 'stay' of effective length 5m is fitted in between the walls of a ships refrigerated compartment when the temperature is 18 degrees centigrade.

  Propane gas enters a continuous adiabatic heat exchanger at

propane gas enters a continuous adiabatic heat exchanger at 40degc and 250 kpa and exits at 240degc superheated steam

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd