A 10 kg slab of cr-v steel at 900 c is to be quenched by

Assignment Help Mechanical Engineering
Reference no: EM13626654

A 10 kg slab of Cr-V steel at 900 C is to be quenched by immersing in a vessel of water. Assume the slab exhibits a spatially uniform temp, T, and there is no heat transfer between water and air. The steel has a surface area of 0.5 m2 Assuming vessel is large enough such that water maintains constant temp of 20 C during quenching, determine average heat transfer coefficient required if steel cooling rate is to be -50 C/sec when T=650 C.

Assuming vessel contains a finite volume of water V = 2m3 which is initially at 20 C prior to quenching, determine average heat transfer coefficient required if steel cooling rate is to be -50 C/sec when T=650C. After quenching, what is final water temp?

Reference no: EM13626654

Questions Cloud

Air enters the compressor section of a turbojet engine at : air enters the compressor section of a turbojet engine at 15 c and 0.1 mpa at a rate of 100 m3min. the air leaves at
The mean number of errors per page made by a clerk in the : the mean number of errors per page made by a clerk in the word processing pool of a bank is thought to be 2.8 with the
Light shines through a single slit whose width is 55 times : light shines through a single slit whose width is 5.5 times 10-4 m. a diffraction pattern is formed on a flat screen
Discuss how the steam power plant steam engine rankine : discuss how the steam power plant steam engine rankine cycle can control the speed of the vehicle during acceleration
A 10 kg slab of cr-v steel at 900 c is to be quenched by : a 10 kg slab of cr-v steel at 900 c is to be quenched by immersing in a vessel of water. assume the slab exhibits a
All elbows are 90 degrees with k factor 075 pipe lengths : for the fluid power system shown in figure determine the external load f that the hydraulic cylinder can sustain while
A company crates its products for shipping as shown base : a company crates its products for shipping as shown base plate with two springs holding a crate- mass suspended in
A sphere 1 ft in diameter is moving horizontally at a depth : a sphere 1 ft in diameter is moving horizontally at a depth of 12ft below water surface where the water temperature is
What focal length lens in cm should be used in the bottom : sometimes a person cannot clearly see objects close up or far away. to correct this type of vision bifocals are often

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd