5 kgm of water is at 15 c and is contained in a vertical

Assignment Help Mechanical Engineering
Reference no: EM13628379

5 kgm of water is at 15 C and is contained in a vertical cylinder by a frictionless piston of a mass such that the pressure of the water is 700 kPa. Heat is transferred slowly to the water, causing the piston to rise until it reaches a set of stops, at which point the volume inside the cylinder is 0.5 m^3. More heat is added to the water until it exists as saturated vapor.

a.) What is the initial volume? (L)
b.) What is the final pressure? (kPa)
c.) What is the total work done? (kJ)
d.) What is the total heat transfer? (kJ)

Reference no: EM13628379

Questions Cloud

In one such experiment the holes are placed every 0500 : to measure the speed of light fizeau used a rotating disk with equally spaced holes through which light could pass.
Water at 70 kpa and 100 c is compressed isentropically in : water at 70 kpa and 100 c is compressed isentropically in a closed system to 5 mpa.determine the final temperature of
Steam enters an adiabatic turbine at 5 mpa and 450 c and : steam enters an adiabatic turbine at 5 mpa and 450 c and leaves at a pressure of 1.4 mpa.determine the work output of
An electron moving in a one- dimensional infinite square : an electron moving in a one- dimensional infinite square well of width l is trapped in the n 5 state. calculate the
5 kgm of water is at 15 c and is contained in a vertical : 5 kgm of water is at 15 c and is contained in a vertical cylinder by a frictionless piston of a mass such that the
In order to have the machine deliver 100000 nmkg of air : air enters a machine at 373 k with a speed of 200 msec and leaves it at the temperature of the standard sea level
The amount of energy transfer to the gas by work is 45 : carbon dioxide co2 gas intially at 70 degrees f 15 lbfin2 and 1 ft3 is compressed in a piston cyclinder assembly.
100 kgm of air is contained in a cylinder by a : 10.0 kgm of air is contained in a cylinder by a free-floating frictionless piston. initially the air is at 27 c and
Estimate the extent of reaction monomer conversion : nylon 12 is produced by step growth polymerization.a estimate the extent of reaction monomer conversion necessary to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  It is observed that snow lies stably on roofs with a slope

question it is observed that snow lies stably on roofs with a slope of less than 24deg but that it slides off roofs

  The incoming air velocity is 100 ms the air density and

consider airflow past a sphere of diameter 5 cm. the incoming air velocity is 100 ms. the air density and temperature

  Determine the maximum shear stress magnitude

A. When the two torques are applied to the composite shaft, determine: the maximum shear stress magnitude in aluminium tube (1), the rotation angle of joint B and c.

  The waste heat from this engine is rejected to a nearby

a heat engine is operating on a carnot cycle and has a thermal efficiency of 55. the waste heat from this engine is

  In an archery test the acceleration of the arrow decreases

in an archery test the acceleration of the arrow decreases linearly with distance s from its initial value of 16000

  What is the specific volume of this r-22 initially b what

five kg of r-22 refrigerant at 3 bar and saturated vapor is contained in a closed rigid tank. a process cools the r-22

  Methane oxygen and nitrogen flow into an insulated tank the

methane oxygen and nitrogen flow into an insulated tank. the methane flow is 2 kgs at the 320k. the oxygen flow is 3

  A tornado rips off a 100 m2 roof with a mass of 1000 kg

a tornado rips off a 100 m2 roof with a mass of 1000 kg. what is the minimum vacuum pressure needed to do that if we

  If we can achieve 10percent of the maximum theoretical work

a flat plate solar collector is to be considered as a means to drive a pump to irrigate crops. this will be used in

  Pump a can empty a tank in four hours while pump b takes

pump a can empty a tank in four hours while pump b takes only three hours to empty the tank. how long will it take to

  At a point on the free surface of a machine part the

at a point on the free surface of a machine part the strains are ex1200 mu ey300mu yxy700 mu. use mohrs circle to

  If the allowable shear stress is 8000 psi and both shafts

a conveyor belt is driven by a 8-hp motor turning at 1500 rpm. through a series of gears that reduce the speed the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd