10 mol of an ideal gas at 5 atm at 298 k is stored in an

Assignment Help Mechanical Engineering
Reference no: EM13630116

10 mol of an ideal gas at 5 atm at 298 K is stored in an insulated piston and cylinder arrangement. At these condition the volume of the gas is 48,900 cm^3. th piston is helf in place by a catch: The gas expands irreversibly against a constaant restraining pressure of 2 atm and the volume of the gas equals 75,000 cm^3. The constant volume heat capacity for this gas is Cv= 35 J/mol.K and the constaant pressure heat capacity of the gas is 43.3 J/mol.K.

1) Draw before and after diagrams ?

2) How much work does the ideal gas go against the restrain?

3) Calculate the final tempreture?

Reference no: EM13630116

Questions Cloud

As observed by the juggler what is the balls total time of : a juggler traveling in a train on level track throws a ball straight up relative to the train with a speed of 6.65 ms.
5 kg of water at 1 atm in a cylinder was heated until it is : 5 kg of water at 1 atm in a cylinder was heated until it is half boiled.1 what is the atm inside the cylinder?2 the
Boral is a commercial shielding material consisting of : boral is a commercial shielding material consisting of approximately equal parts by weight of boron carbide b4c and
A similar one-week study with mountain communications : there are two major internet providers in the colorado springs colorado area one called htc and the other mountain
10 mol of an ideal gas at 5 atm at 298 k is stored in an : 10 mol of an ideal gas at 5 atm at 298 k is stored in an insulated piston and cylinder arrangement. at these condition
A cold heading operation is performed to produce the head : a cold heading operation is performed to produce the head on a steel nail. the strength coefficient for this steel is
There are 10 swedes and 7 finns we should choose a : there are 10 swedes and 7 finns. we should choose a committee that consists of 9 people. the committee has a chairman
Hw much electricity does the pump consume the pump is 70 : 14 kgs of liquid water enters a pump at a velocity of 1 ms and at 1 atm pressure. it leaves the pump at a velocity of
A pound of air is used in a carnot power cycle at a : a pound of air is used in a carnot power cycle. at a constant 1540of the pressure goes from 2710 psia to 1882 psia.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd